For additional information regarding your printer, please see the user manuals linked below
Table of contents:
Epson M30-III: The latest Snack receipt printer.
Setup
Place the printer in the desired location on or below the counter
Assemble the power cable by plugging the two cables together at the power brick.
Remove the rear & bottom plate(s) to connect the power cord.
To remove the rear & bottom covers, start by placing your fingers in the opening located at back/bottom of the printer and pull away from the printer
Note
:For all models, do not pull too hard to avoid damage to the printer; very little force is needed to remove the plate.
Additionally, you may need to free the cable channel by simply bending & removing the pre-cut tab(s). Do not throw this piece away as it can be re-installed.
With the back plate(s) removed, plug the power cord into the printer
For proper alignment: Have the flat face at the end of the power cord facing outward with the arrow pointing towards the power port. If connecting to the internet through an ethernet connection, insert the ethernet cable at this time.
Important Notice:
Our support team can assist you with WiFi setup & troubleshooting for Epson TM-m30-III printers only after you have followed this guide. We prioritize Ethernet connections for optimal performance.
Station Printers (Chit) - Self-setup via WiFi is allowed, support is limited.
Food Trucks - Bluetooth connections are acceptable & support is available.
Please refer to our guide for WiFi self-setup in kitchen stations. For full support, use Ethernet.
5. Plug the opposite end of the power cord into a power outlet
Note: Use an extension cord or power strip as needed
6. After connecting the printer to the outlet, if the LED panel on the printer lights up, the printer is on.
For a cash drawer installation: follow this guide
Follow the directions below, place the backing plates back onto the printer.
Line the top of the backing plate up with the flat part on the top/back of the printer. Fit the cords into the opening at the bottom of the plate and press the plate in
Note:
Your printers are shipped to you with a paper roll already installed. Once that paper roll is finished, you will need to replace with a new paper roll
Receipt Printer WiFi setup
Getting the SimpleAP Start Printout
First, turn the printer on by pressing the power button. Wait for a moment while it powers up. The printer will automatically print a SimpleAP Start page. This page contains critical information including a QR code and the “SSID” (Network Name) for the printers onboard network.
Note: If a USB or Ethernet cable is connected to the printer, the SimpleAP Start page will not automatically print.
Scan the QR Code on the SimpleAP Start Page
Next, open the camera app on your smartphone or tablet. Point the camera at the QR code on the SimpleAP Start page. A notification should appear on your phone prompting you to join the network shown in the “SSID” section of the SimpleAP Start page. Tap the notification and accept the request to join the network.
WebConfig Start Page
Once you have joined the network, the printer will print a WebConfig Start page. Open the camera app on your smartphone or tablet again and scan the QR code on the WebConfig Start page. If the WebConfig Start page does not automatically print, you will need to manually go to your device’s Wi-Fi settings. Connect to the Wi-Fi network shown in the “SSID” section of the SimpleAP Start page.
Select Wi-Fi in the WebConfig (Website Configuration).
Enter the Printer’s Serial Number as Password
When prompted, enter the printer’s serial number as the password. The serial number can typically be found on a sticker on the side or bottom of the printer. After entering the serial number, select OK.
Note: The last 10 digits in the ”SSID” section of the SimpleAP Start page show the printer’s serial number.
Select your Wi-Fi Network.
In the WebConfig interface, a list of available Wi-Fi networks will be displayed. Select the Wi-Fi network you want the printer to connect to, and then click or tap on OK to confirm your selection.
Note: If you want to connect the printer to the Snackpass provided router, you can contact our support team by going to the "Get Help" tab on the top right, and sending our team a message!
Enter Network Password
Confirmation
The printer will now perform the connection process. Once connected, the printer will automatically print a network status page. The network status page confirms that your printer is now successfully connected to the Wi-Fi network. You can now close the web page on your device. Your Epson M30-III Receipt Printer is ready for use.
Your Epson M30-III Receipt Printer is now set up and connected to the Wi-Fi network. If you encounter any issues, refer to the installation guide for troubleshooting steps.